This is the latest recevied telemetry packets stored in our database for station/object 3Z2T-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Value1* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1749279704 | 30 | 438 | 0 | 410 | 219 |
| 1749277903 | 28 | 431 | 0 | 410 | 219 |
| 1749276103 | 26 | 418 | 0 | 410 | 219 |
| 1749274305 | 24 | 406 | 0 | 410 | 219 |
| 1749272505 | 22 | 390 | 0 | 410 | 220 |
| 1749268906 | 18 | 371 | 0 | 410 | 220 |
| 1749267105 | 16 | 355 | 0 | 410 | 215 |
| 1749265306 | 14 | 326 | 0 | 410 | 147 |
| 1749263507 | 12 | 296 | 0 | 410 | 87 |
| 1749261706 | 10 | 262 | 0 | 410 | 50 |
| 1749259906 | 8 | 224 | 0 | 410 | 50 |
| 1749258107 | 6 | 189 | 0 | 410 | 50 |
| 1749256309 | 4 | 160 | 0 | 410 | 50 |
| 1749254507 | 2 | 105 | 0 | 410 | 50 |
| 1749252708 | 0 | 38 | 0 | 410 | 50 |
| 1749250908 | 83 | 995 | 0 | 410 | 50 |
| 1749249109 | 81 | 917 | 0 | 411 | 50 |
| 1749245511 | 77 | 806 | 0 | 411 | 50 |
| 1749243710 | 75 | 761 | 0 | 411 | 50 |
| 1749241911 | 73 | 725 | 0 | 411 | 50 |
| 1749240111 | 71 | 678 | 0 | 411 | 50 |
| 1749238311 | 69 | 625 | 0 | 411 | 50 |
| 1749236512 | 67 | 591 | 0 | 411 | 96 |
| 1749234714 | 65 | 544 | 0 | 411 | 181 |
| 1749232913 | 63 | 514 | 0 | 412 | 77 |
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)