This is the latest recevied telemetry packets stored in our database for station/object SR2JP-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1757178469 | 190 Count | 361 Count | 20 Count | 0 VDC | 0 VDC |
| 1757176788 | 186 Count | 358 Count | 20 Count | 0 VDC | 0 VDC |
| 1757175108 | 181 Count | 356 Count | 20 Count | 0 VDC | 0 VDC |
| 1757173427 | 178 Count | 353 Count | 20 Count | 0 VDC | 0 VDC |
| 1757171994 | 171 Count | 350 Count | 20 Count | 0 VDC | 0 VDC |
| 1757170313 | 166 Count | 347 Count | 20 Count | 0 VDC | 0 VDC |
| 1757168632 | 163 Count | 339 Count | 20 Count | 0 VDC | 0 VDC |
| 1757166951 | 158 Count | 337 Count | 20 Count | 0 VDC | 0 VDC |
| 1757165271 | 154 Count | 334 Count | 20 Count | 0 VDC | 0 VDC |
| 1757163590 | 150 Count | 331 Count | 20 Count | 0 VDC | 0 VDC |
| 1757161909 | 145 Count | 328 Count | 20 Count | 0 VDC | 0 VDC |
| 1757160228 | 141 Count | 325 Count | 20 Count | 0 VDC | 0 VDC |
| 1757158548 | 137 Count | 322 Count | 20 Count | 0 VDC | 0 VDC |
| 1757156866 | 132 Count | 317 Count | 20 Count | 0 VDC | 0 VDC |
| 1757155186 | 128 Count | 314 Count | 20 Count | 0 VDC | 0 VDC |
| 1757153505 | 123 Count | 312 Count | 20 Count | 0 VDC | 0 VDC |
| 1757151824 | 119 Count | 309 Count | 20 Count | 0 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)