EA2RCF LoRa APRS MAP

My position About Go to BACKUP map Powered by EA2RCF Radioclub Foronda ☰

reset

LZ0VRC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ0VRC-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Humi*	Presaure*	Power*
1769970716	82.8 %RH	972 hPa	5.61 V
1769970416	82.8 %RH	972 hPa	5.6 V
1769970410	82.8 %RH	972 hPa	5.65 V
1769970116	82.8 %RH	972 hPa	5.64 V
1769969816	82.8 %RH	972 hPa	5.66 V
1769969810	82.8 %RH	972 hPa	5.66 V
1769969516	82.8 %RH	972 hPa	5.68 V
1769969216	82.8 %RH	972 hPa	5.59 V
1769969210	82.8 %RH	972 hPa	5.59 V
1769968916	82.8 %RH	972 hPa	5.62 V
1769968616	82.8 %RH	972 hPa	5.59 V
1769968610	82.8 %RH	972 hPa	5.61 V
1769968316	82.8 %RH	972 hPa	5.66 V
1769968016	82.8 %RH	972 hPa	5.61 V
1769968010	82.8 %RH	972 hPa	5.6 V
1769967716	82.8 %RH	972 hPa	5.64 V
1769967416	82.8 %RH	972 hPa	5.61 V
1769967410	82.8 %RH	972 hPa	5.61 V
1769967116	82.8 %RH	972 hPa	5.68 V
1769966816	82.8 %RH	972 hPa	5.62 V
1769966810	82.8 %RH	972 hPa	5.62 V
1769966516	82.8 %RH	972 hPa	5.62 V
1769966216	82.8 %RH	972 hPa	5.59 V
1769966210	82.8 %RH	972 hPa	5.68 V
1769965916	82.8 %RH	972 hPa	5.62 V

*Used Equation Coefficients:

Temp: 0, 0.01, 0

Humi: 0, 0.01, 0

Presaure: 0, 1, 0

Power: 0, 0.01, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)