This is the latest recevied telemetry packets stored in our database for station/object 3Z2T-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Value1* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1765594415 | 34 | 445 | 0 | 411 | 0 |
| 1765592615 | 33 | 433 | 0 | 411 | 0 |
| 1765590817 | 32 | 420 | 0 | 411 | 0 |
| 1765589018 | 31 | 408 | 0 | 412 | 0 |
| 1765587219 | 30 | 396 | 0 | 412 | 0 |
| 1765585420 | 29 | 377 | 0 | 412 | 0 |
| 1765583620 | 28 | 364 | 0 | 412 | 0 |
| 1765581821 | 27 | 354 | 0 | 412 | 0 |
| 1765580022 | 26 | 342 | 0 | 412 | 0 |
| 1765578224 | 25 | 332 | 0 | 412 | 0 |
| 1765574626 | 23 | 305 | 0 | 412 | 0 |
| 1765572827 | 22 | 294 | 0 | 412 | 0 |
| 1765571027 | 21 | 283 | 0 | 412 | 0 |
| 1765569229 | 20 | 272 | 0 | 412 | 0 |
| 1765567430 | 19 | 260 | 0 | 412 | 0 |
| 1765565631 | 18 | 250 | 0 | 412 | 0 |
| 1765562032 | 16 | 220 | 0 | 413 | 0 |
| 1765560232 | 15 | 208 | 0 | 413 | 0 |
| 1765558434 | 14 | 194 | 0 | 413 | 0 |
| 1765556635 | 13 | 184 | 0 | 413 | 0 |
| 1765554835 | 12 | 167 | 0 | 413 | 0 |
| 1765553037 | 11 | 153 | 0 | 413 | 0 |
| 1765551236 | 10 | 140 | 0 | 413 | 0 |
| 1765549439 | 9 | 109 | 0 | 413 | 0 |
| 1765547639 | 8 | 100 | 0 | 413 | 123 |
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)