This is the latest recevied telemetry packets stored in our database for station/object 9W2GDB-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1765593719 | 310 Count | 467 Count | 296 Count | 4.02 VDC | 0.08 VDC |
| 1765591917 | 305 Count | 453 Count | 292 Count | 4.03 VDC | 0.08 VDC |
| 1765590113 | 300 Count | 432 Count | 288 Count | 4.02 VDC | 0.08 VDC |
| 1765588309 | 295 Count | 425 Count | 284 Count | 4.02 VDC | 0.08 VDC |
| 1765586504 | 290 Count | 418 Count | 280 Count | 4.03 VDC | 0.08 VDC |
| 1765584700 | 285 Count | 411 Count | 276 Count | 4.02 VDC | 0.08 VDC |
| 1765582891 | 280 Count | 404 Count | 272 Count | 4.02 VDC | 0.08 VDC |
| 1765581086 | 275 Count | 397 Count | 268 Count | 4.02 VDC | 0.08 VDC |
| 1765579282 | 270 Count | 390 Count | 264 Count | 4.02 VDC | 0.08 VDC |
| 1765577477 | 265 Count | 383 Count | 260 Count | 4.02 VDC | 0.08 VDC |
| 1765575672 | 260 Count | 376 Count | 256 Count | 4.02 VDC | 0.08 VDC |
| 1765574029 | 255 Count | 369 Count | 252 Count | 4.03 VDC | 0.08 VDC |
| 1765572224 | 250 Count | 362 Count | 248 Count | 4.03 VDC | 0.08 VDC |
| 1765570420 | 245 Count | 356 Count | 244 Count | 4.03 VDC | 0.08 VDC |
| 1765568615 | 240 Count | 350 Count | 240 Count | 4.04 VDC | 0.08 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)