This is the latest recevied telemetry packets stored in our database for station/object S56JGE-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | V_Batt* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1769954928 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769951448 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769949707 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769946227 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769944487 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769942746 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769941006 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769939266 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769937526 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769935786 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769934046 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769932305 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769930565 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769928825 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769927088 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769925345 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769923605 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769921864 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769920124 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769918383 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769916643 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769914902 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769913162 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769911422 | 4.19 VDC | 0 | 0 | 0 | 0 |
| 1769909682 | 4.19 VDC | 0 | 0 | 0 | 0 |
*Used Equation Coefficients:
V_Batt: 0, 0.01, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)