This is the latest recevied telemetry packets stored in our database for station/object SP5BWN-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | V_Bat* | V_Ext* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1749334058 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749334003 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333942 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333916 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333903 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333859 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333846 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333785 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333731 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333718 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333705 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333692 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333668 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333640 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333579 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333564 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333506 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333489 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333428 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333392 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333372 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333359 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333336 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333323 | 0 VDC | 0 VDC | 0 | 0 | 0 |
| 1749333296 | 0 VDC | 0 VDC | 0 | 0 | 0 |
*Used Equation Coefficients:
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)