This is the latest recevied telemetry packets stored in our database for station/object M7PDA-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1757273031 | 465 Count | 472 Count | 321 Count | 0 VDC | 0 VDC |
| 1757271228 | 456 Count | 459 Count | 313 Count | 0 VDC | 0 VDC |
| 1757269424 | 449 Count | 452 Count | 307 Count | 0 VDC | 0 VDC |
| 1757267621 | 444 Count | 446 Count | 303 Count | 0 VDC | 0 VDC |
| 1757265858 | 439 Count | 441 Count | 299 Count | 0 VDC | 0 VDC |
| 1757264055 | 434 Count | 436 Count | 295 Count | 0 VDC | 0 VDC |
| 1757262252 | 429 Count | 431 Count | 291 Count | 0 VDC | 0 VDC |
| 1757260449 | 424 Count | 425 Count | 287 Count | 0 VDC | 0 VDC |
| 1757258646 | 419 Count | 420 Count | 283 Count | 0 VDC | 0 VDC |
| 1757256843 | 414 Count | 415 Count | 279 Count | 0 VDC | 0 VDC |
| 1757255039 | 409 Count | 409 Count | 275 Count | 0 VDC | 0 VDC |
| 1757253236 | 404 Count | 404 Count | 271 Count | 0 VDC | 0 VDC |
| 1757251433 | 399 Count | 399 Count | 267 Count | 0 VDC | 0 VDC |
| 1757247827 | 389 Count | 388 Count | 259 Count | 0 VDC | 0 VDC |
| 1757246024 | 383 Count | 382 Count | 254 Count | 0 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)