This is the latest recevied telemetry packets stored in our database for station/object IV3CGJ-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | V_Batt* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1761127718 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761126818 | 4.26 VDC | 0 | 0 | 0 | 0 |
| 1761125917 | 4.25 VDC | 0 | 0 | 0 | 0 |
| 1761125017 | 4.25 VDC | 0 | 0 | 0 | 0 |
| 1761124117 | 4.22 VDC | 0 | 0 | 0 | 0 |
| 1761123217 | 4.26 VDC | 0 | 0 | 0 | 0 |
| 1761123149 | 4.29 VDC | 0 | 0 | 0 | 0 |
| 1761122317 | 4.28 VDC | 0 | 0 | 0 | 0 |
| 1761121417 | 4.22 VDC | 0 | 0 | 0 | 0 |
| 1761120517 | 4.21 VDC | 0 | 0 | 0 | 0 |
| 1761119617 | 4.28 VDC | 0 | 0 | 0 | 0 |
| 1761118716 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761117816 | 4.24 VDC | 0 | 0 | 0 | 0 |
| 1761116916 | 4.29 VDC | 0 | 0 | 0 | 0 |
| 1761116016 | 4.29 VDC | 0 | 0 | 0 | 0 |
| 1761115115 | 4.25 VDC | 0 | 0 | 0 | 0 |
| 1761114215 | 4.25 VDC | 0 | 0 | 0 | 0 |
| 1761113315 | 4.29 VDC | 0 | 0 | 0 | 0 |
| 1761112415 | 4.22 VDC | 0 | 0 | 0 | 0 |
| 1761111515 | 4.28 VDC | 0 | 0 | 0 | 0 |
| 1761110615 | 4.25 VDC | 0 | 0 | 0 | 0 |
| 1761109714 | 4.29 VDC | 0 | 0 | 0 | 0 |
| 1761108814 | 4.24 VDC | 0 | 0 | 0 | 0 |
| 1761107914 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761107011 | 4.28 VDC | 0 | 0 | 0 | 0 |
*Used Equation Coefficients:
V_Batt: 0, 0.01, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)