This is the latest recevied telemetry packets stored in our database for station/object MB7ULM-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | V_Batt* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1761137804 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761136904 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761136004 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761135104 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761134204 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761133304 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761132404 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761131504 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761130604 | 4.22 VDC | 0 | 0 | 0 | 0 |
| 1761129704 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761128804 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761127904 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761126103 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761125203 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761124303 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761123403 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761122503 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761121603 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761120703 | 4.22 VDC | 0 | 0 | 0 | 0 |
| 1761119803 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761118903 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761118002 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761117104 | 4.22 VDC | 0 | 0 | 0 | 0 |
| 1761116204 | 4.23 VDC | 0 | 0 | 0 | 0 |
| 1761115304 | 4.23 VDC | 0 | 0 | 0 | 0 |
*Used Equation Coefficients:
V_Batt: 0, 0.01, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)