This is the latest recevied telemetry packets stored in our database for station/object IZ4FTD-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Voltage* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1764705679 | 2.96 VDC | 0 | 0 | 0 | 0 |
| 1764700058 | 3.38 VDC | 0 | 0 | 0 | 0 |
| 1764699108 | 3.1 VDC | 0 | 0 | 0 | 0 |
| 1764695353 | 3.5 VDC | 0 | 0 | 0 | 0 |
| 1764695112 | 3.48 VDC | 0 | 0 | 0 | 0 |
| 1764694784 | 3.47 VDC | 0 | 0 | 0 | 0 |
| 1764694545 | 3.43 VDC | 0 | 0 | 0 | 0 |
| 1764694061 | 3.23 VDC | 0 | 0 | 0 | 0 |
| 1764682196 | 3.33 VDC | 0 | 0 | 0 | 0 |
| 1764676616 | 2.98 VDC | 0 | 0 | 0 | 0 |
| 1764674673 | 3.35 VDC | 0 | 0 | 0 | 0 |
| 1764674447 | 3.22 VDC | 0 | 0 | 0 | 0 |
| 1764659269 | 3.56 VDC | 0 | 0 | 0 | 0 |
| 1764659037 | 3.56 VDC | 0 | 0 | 0 | 0 |
| 1764658267 | 3.53 VDC | 0 | 0 | 0 | 0 |
| 1764657883 | 3.52 VDC | 0 | 0 | 0 | 0 |
| 1764657626 | 3.51 VDC | 0 | 0 | 0 | 0 |
| 1764657090 | 3.43 VDC | 0 | 0 | 0 | 0 |
| 1764656830 | 3.28 VDC | 0 | 0 | 0 | 0 |
*Used Equation Coefficients:
Voltage: 0, 0.01, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)