This is the latest recevied telemetry packets stored in our database for station/object SR2ST-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1755894460 | 424 Count | 430 Count | 63 Count | 0 VDC | 0 VDC |
| 1755893029 | 406 Count | 421 Count | 62 Count | 0 VDC | 0 VDC |
| 1755891348 | 362 Count | 398 Count | 61 Count | 0 VDC | 0 VDC |
| 1755889668 | 346 Count | 375 Count | 60 Count | 0 VDC | 0 VDC |
| 1755887987 | 325 Count | 344 Count | 58 Count | 0 VDC | 0 VDC |
| 1755886306 | 303 Count | 312 Count | 56 Count | 0 VDC | 0 VDC |
| 1755884625 | 286 Count | 280 Count | 55 Count | 0 VDC | 0 VDC |
| 1755881264 | 260 Count | 252 Count | 53 Count | 0 VDC | 0 VDC |
| 1755879583 | 245 Count | 241 Count | 52 Count | 0 VDC | 0 VDC |
| 1755877902 | 228 Count | 229 Count | 49 Count | 0 VDC | 0 VDC |
| 1755876221 | 207 Count | 213 Count | 45 Count | 0 VDC | 0 VDC |
| 1755874540 | 187 Count | 186 Count | 42 Count | 0 VDC | 0 VDC |
| 1755872859 | 161 Count | 141 Count | 35 Count | 0 VDC | 0 VDC |
| 1755871429 | 138 Count | 126 Count | 30 Count | 0 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)